RSS
Research

Fable 5.2 designs three working circuit boards

Working with PCB maker Diode, Anthropic had Claude Fable 5.2 design a USB speakerphone, a voice-assistant hub and a handheld virtual pet, from schematic to enclosure and firmware. The boards worked without circuit fixes. What it did and where it fell short.

blue circuit board
Photo by Umberto on Unsplash

Updated November 20, 2026: Expanded with how Claude laid out and revised the boards, the router it wrote, the manufacturing checks, benchmark scores and the limits.

Anthropic published a research post on November 9 describing how Claude Fable 5.2 designed three electronic devices with minimal prompting: a USB speakerphone, a voice-assistant hub and a battery-powered handheld virtual pet. The work was done with Diode Computers, a company that designs and manufactures circuit boards and that Anthropic says it has a commercial relationship with. Diode's engineers assembled and tested the prototypes under Claude's direction; Claude itself was not connected to test or production equipment. Anthropic reports that all three worked without any fixes to their circuitry. Everything below comes from Anthropic's own posts, not independent testing.

What Claude was asked to do

Each device started from a short prompt describing what to build and its main hardware needs. The speakerphone prompt, for example, asked for a USB-C puck with microphones, a speaker and Bluetooth through a PCB antenna. From there Claude wrote the specifications, drew the schematics, placed components on the printed circuit board, routed the copper connections, designed a 3D-printable enclosure, wrote the firmware and prepared a parts list. The Fable 5.2 launch post adds that it picked components available from US distributors, routed four-layer boards, and had each board ready for manufacturing in under a day. Anthropic's posts do not say whether the design files, firmware or full prompts are published. Anthropic says the Diode team's prompting was minimal, mostly short directives such as continue or clean up the schematic.

How it handled the hard parts

  • Layout: Fable 5.2 routed the sensitive connections first. On the hub it started with the USB and Ethernet pairs, keeping each pair the same length and correctly spaced, and added small zigzag tuning patterns so signals arrive together.
  • Revising its own work: earlier models rarely backtracked, and Diode says many boards it designed with them were 95% complete but still unusable. Fable 5.2 reassigned chip pins on the speakerphone so tracks under its touch controls could stay on one layer, and on the hub it ripped up and rerouted connections dozens of times when they got too tangled.
  • Reading datasheets: asked whether the pet would run without a battery, it read the charger's datasheet and predicted it would run on USB power but the charging light would flicker, because the charger keeps recharging a small capacitor in the battery's place.
  • Physical fit: it wrote code to check the board fits its enclosure and found the speakerphone board could not drop straight in, because the mute switch knob would hit the back wall; it worked out a tilt of about 25 degrees and added that to the assembly instructions. For the hub, it calculated that a 25 mm microphone port would resonate near 3.4 kHz, in the voice band, and switched to a wedge-shaped case that cut the port to about 10 mm, moving the resonance to about 8.9 kHz, at the edge of the speech range. It also wrote speakerphone firmware that dims the LED ring as volume rises, to stay under the board's current limit.
  • Manufacturing checks: it ran design-for-manufacturing and parts-sourcing checks, fixed six solder-mask slivers that were too thin, and correctly ignored a flag on a deliberate ground connection.

The router it wrote for itself

The detail most people noticed came while routing the hub. Diode's setup let Claude drive the router built into KiCad, a widely used board design program, but that router laid one track at a time between points Claude had to choose. The hub had long tracks running from a 100-pin connector, and Claude judged that doing them one by one would take too much step-by-step guidance. So it wrote its own grid-based router. Within about half an hour it had a tool that laid each long track in roughly a second, and when it noticed an audio clock track running too close to the Ethernet lines, it changed the router to leave more room around sensitive tracks.

Benchmarks

Diode ran PCB Gym, an internal benchmark that removes the layout from real board designs and scores how well a model places components and reroutes connections. Fable 5.2 scored 69%, against 25% for Fable 5. On BenchCAD 2.1, a public benchmark for rebuilding 3D parts, assemblies and boards from drawings, Anthropic reports 83.5 for Fable 5.2 at Max effort, ahead of Opus 5.5 at 65.3 and Fable 5.1 at 44.4. These are Anthropic's and Diode's own numbers.

Limits

Anthropic is clear that these are early prototypes. They have not been through electrical validation, antenna tuning, thermal testing or certification, and were not designed for mass production. Diode's engineers built and tested everything physically. Anthropic says the speakerphone still works after weeks of use and the other two are in good working order, but long-term reliability is unknown. Next, it plans to try denser, faster boards, check them in simulation and learn from measurements on finished devices. Anthropic also notes other labs are making similar progress, citing an OpenAI write-up about designing a handheld device.

Fable 5.2 is available to all users, including on AWS, Google Cloud and Microsoft Azure, and on the API as claude-fable-5-2 at a standard $8 per million input tokens and $40 per million output tokens; an optional fast mode costs $16 and $80. Claude Mythos 5.2 is the same underlying model, but access requires applying through Anthropic's verification programs for cybersecurity or life sciences work.

Our take

The router is the telling part. When the tool it was handed was too slow, the model built a better one in half an hour and kept tuning it. In our view, for small hardware teams the near-term interest is speed from idea to a first working prototype; validation, certification and production work still belongs to engineers, and these results are self-reported by Anthropic and a commercial partner.

Source: Testing Claude on real-world electronics design (Anthropic), Introducing Claude Fable 5.2 and Claude Mythos 5.2 (Anthropic)

This story first appeared in the claudefox daily briefing for November 10, 2026.